CONNECT EVERYTHING
The C 379 is well equipped with a variety of analogue and digital connectivity options including aptX HD Bluetooth, HDMI eARC, MM Phono stage, and two subwoofer outputs. aptX HD can easily support 24-bit streaming from any Bluetooth enabled device, while HDMI eARC allows you to connect the C 379 to your TV and provide seamless control from your existing remote. It also includes a built-in high-performance headphone amplifier with low output impedance and high output voltage capability, allowing it to drive a wide range of headphones.
Features & Details
- Customised HybridDigital UcD Amplifier with Stereo and Bridge Modes
- 2 x 80 Watts per channel of Continuous Power (8 and 4 Ohms)
- 2 x 120 Watts per channel of Dynamic Power (4 Ohms)
- Bridgeable for up to 300 Watts per channel of Continuous Power
- Industry-leading ESS SABRE® PRO 32-bit/384kHz DAC
- Dual MDC 2 Ports for Future Upgrades and Expanded Features
- MM Phono Stage with Accurate RIAA Equalization and Ultra-Low Noise
- Built-in Separate Headphone Amplifier for Low and High Impedance
- HDMI eARC, Optical Digital and Coax Digital Inputs
- Dual Subwoofer Outputs
PREAMPLIFIER SECTION
LINE INPUT, PRE-OUT (ANALOG BYPASS ON)
- THD (20Hz – 20kHz)
- <0.002 % at 2 V out
- Signal-to-Noise Ratio
- >106dB (IHF; A-weighted, ref. 500 mV out, unity gain)
- Channel separation
- >100dB (1 kHz); >90 dB (10 kHz)
- Input Impedance (R and C)
- 56.2 kohms + 100 pF
- Maximum input signal
- >4.6 Vrms (ref. 0.1 % THD)
- Output impedance
- Source Z + 320 ohms
- Input sensitivity
- 257 mV (ref. 500 mV out, Volume maximum)
- Frequency response
- ±0.3 dB (20 Hz – 20 kHz)
- Maximum voltage output -IHF load
- >4.5 V (ref. 0.1 % THD)
PHONO INPUT, PRE-OUT (ANALOG BYPASS ON)
- THD (20Hz – 20kHz)
- <0.01% at 2 V out
- Signal-to-Noise Ratio
- >83dB (200 ohms source; A-weighted, ref. 500 mV out)
- Input sensitivity
- 46 kohms/100 pF
- Frequency response
- ±0.3 dB (20 Hz – 20 kHz)
- Maximum input signal at 1kHz
- >80 mVrms (ref. 0.1 % THD)
LINE INPUT, HEADPHONE OUT (ANALOG BYPASS ON)
- THD (20Hz – 20kHz)
- <0.002% at 1V out
- Signal-to-Noise Ratio
- >101 dB (32 ohms loads; A-WTD, ref. 1V out, unity gain
- Frequency response
- ±0.3 dB (20 Hz – 20 kHz)
- Channel separation
- >62 dB at 1kHz
- Output impedance
- 2.2 Ohms
GENERAL SPECIFICATIONS
LINE IN, SPEAKER OUT (ANALOG BYPASS ON)
- Continuous output power into 8 ohms
- 80W (ref. 20 Hz-20 kHz at rated THD, both channels driven)
- Continuous output power into 8 Ohms (Bridge mode)<s/trong>
- >300W
- THD (20 Hz – 20 kHz)
- <0.03% (250 mW to 120 W, 8 ohms and 4 ohms)
- Signal-to-Noise Ratio
- >85 dB (A-weighted, 500 mV input, ref. 1 W out in 8 ohms)
- Clipping power
- >110W (at 1 kHz 0.1 % THD)
- IHF dynamic power
- 8 ohms: 140W
- 4 ohms: 250W
- 2 ohms: 260W
- Peak output current
- >20A (in 1 ohm, 1ms)
- Damping factor
- >300 (ref. 8 ohms, 20Hz to 6.5kHz)
- Frequency response
- >±0.3 dB (20 Hz – 20 kHz)
- Channel separation
- >75dB (1 kHz)
- >70dB (10 kHz)
- Input sensitivity (for 80 W in 8 ohms)
- Line In: 440 mV
- Supports bit rate/sample rate
- up to 24 bit/192 kHz
- Frequency band
- 2.402G- 2.480G
- Standby power
- >0.5W
- Network standby power
- >2W
DIMENSIONS AND WEIGHT
- Gross dimensions (W x H x D)**
- 435 x 100 x 410mm (17 1/4 x 4 x 16 3/16 inches)
- Net Weight
- 9.04 kg
- Shipping weight
- 10.88 kg
Software & Downloads
FIRMWARE
To download a copy of the firmware for your NAD unit, please contact support